The new Castle Creations Thunderbird series 36 Amp and 54 Amp ESCs are here at Draganfly Innovations Inc. www.RCToys.com. These new Castle Creations Thunderbird brushless motor electronic speed controllers (ESC) are perfect for using with a lithium polymer battery and brushless motor in your favorite rc heli, plane, car, truck or boat. The Castle Creations Thunderbird 36A ESC and the Castle Creations Thunderbird 54A ESC both offer a long list of advanced features like BEC (battery eliminator circuit) to ensure your Lipo battery does not over discharge, a safe “power on” with audible arming signal, automatic motor cut-off with reset and all with a super simple setup. These new Castlecreations Thunderbird brushless controllers are also compatible with the Castle Link USB programmer.

Suggested accessories for a the Castle Creations Thunderbird 36 Amp Brushless Speed Controller

• Hacker A30-10XL Brushless Motor
• Berg 7P Receiver
• APC 12×8 Prop
• Thunder Power 3s4200 Lipo

Suggested accessories for a the Castle Creations Thunderbird 54 Amp Brushless Speed Controller

• Himax HC3528-1000 Brushless Motor
• Berg 7P Receiver
• APC 11×7 Prop
• Thunder Power 3s3300 Lipo

Get FREE Shipping today on all new Castle Creations Thunderbird Brushless Speed Controllers at Draganfly Innovations Inc. www.RCToys.com. With our MAP prices and FREE Shipping this is the best deal you’re going to find on the ‘Net. Pick up a new Thunderbird ESC today!

——
© Draganfly Innovations Inc.
Phone: 1-800-979-9794 / 306-955-9907
Email: info@rctoys.com
Web: www.rctoys.com
RSS: www.rctoys.com/pr/feed

The LipoSack is a hi-tech bag made of space-age materials that has the ability to contain a lithium polymer battery fire or charging mishap. Place your lithium polymer battery inside the LipoSack and extend the charging wires through the top flap. Charge the lipo batteries when they’re in the LipoSack for peace of mind and greater safety. In the case of a lithium polymer battery charging mishap, the Lipo Sack’s fire-resistant material mitigates the ferocity of the LiPoly blaze inside and vents the smoke outside the Lipo Sack.

The LipoSack is about the size of a letter-size envelope. It measures 9×12 inches (22.9 by 30.5 cm) and weights 10 ounces (284g). The LipoSack is sealed with a thick, industrial strength, Velcro flap. The current LipoSack is designed to handle a lithium polymer battery mishap from 1 to 6 lipoly cells (1s to 6s).

Watch a video of the LipoSack with exploding LiPoly batteries inside. See how the LipoSack protects the environment around the LipoSack and mitigates the brunt of the explosions and fire inside the LipoSack. The smoke vents outside.

Play LipoSack Flash Video Play LipoSack Windows Media Video

Before using the LipoSack you must read and understand the LipoSack Safety Instructions. The manufacturer, LipoSack.com, and Draganfly Innovations Inc. assume absolutely no liability for any damages of any kind - even with proper use. When using the LipoSack, you must always remember to abide by safe lithium polymer battery charging and safety rules and never leave charging li-polymer batteries unattended. Never leave damaged lipos unattended. Always use the LipoSack on a non-flammable surface and in a ventilated area. Avoid damage to the LipoSack and not use the LipoSack if it is damaged. For an in-depth discussion on the LipoSack read this RCGroups forum.

Draganfly Innovations Inc. www.RCToys.com now offers the LipoSack for sale on our Web site. Purchase a LipoSack today and gain peace of mind of using this safer charging solution. “Lipo Safety… It’s In The Bag!”

——
© Draganfly Innovations Inc.
Phone: 1-800-979-9794 / 306-955-9907
Email: info@rctoys.com
Web: www.rctoys.com
RSS: www.rctoys.com/pr/feed

First, make sure the Draganflyer battery is fully charged, and that the transmitter battery is fully charged. Check that the transmitter antenna is fully tightened and that the wire circuit board antenna on the Draganflyer RC helicopter is not loose.

Check if the transmitter crystal is plugged in all the way (this would be on the front of the transmitter in the bottom corner, or on the back in the top middle). Inspect the receiver module on the Draganflyer main circuit board. This is the part that is on the side above the arming button. The pins on this part should be plugged in all the way, so that none of the metal on the pins is exposed.

When the Draganflyer receives radio signals properly, before pressing the arming button, the red LED should blink fast when the throttle is at max, and slow when the throttle is at the lowest setting.

——
© Draganfly Innovations Inc.
Phone: 1-800-979-9794 / 306-955-9907
Email: info@rctoys.com
Web: www.rctoys.com
RSS: www.rctoys.com/pr/feed